Washing Your Brace by Hand
Remove any plastic or metal pieces from the brace if you can. These parts can become damaged or may even cause damage to the fabric during washing. Place them off to the side. If your plastic or metal pieces are dirty, then you can wipe them down with a soapy towel. Then pat them dry with a towel. If you can’t remove the pieces, then close your brace before washing it. This helps protect the clasps.
Fill your sink, tub, or a container with cool water. Cool water is easier on the fabric and eliminates the risk of burning your hands. Make sure you have enough water to fully cover the brace. Your wash bin should be clean. Avoid using hot water, as it is harsh on the fabric. Don’t put the brace in first. It’s important that detergent be put in before the brace, as this puts less stress on the fabric.
Add 1 teaspoon (4.9 mL) of mild laundry detergent to the water. You can add more detergent if you’d like, but keep in mind that it can stress the fabric if you add too much. Use your hands to swirl the water, mixing in the detergent. You can also wash your brace with a mixture of equal parts baking soda and vinegar. This will clean the brace and eliminate odors. The smell of vinegar will evaporate, but you can also mask it with an essential oil.
Press the brace down into the water to saturate it. Don’t twist the brace or rub it against the sides of the bin, as this can cause damage. Simply push the brace down with your fingers until the water soaks in. You may see sweat or dirt come out of the brace, and that’s okay.
Allow the brace to soak for about 30 minutes. Once the brace is saturated, it just needs to soak. This allows the detergent to remove the sweat, dirt, and oils that may be trapped in the fabric. If your water is dirty after you saturate the brace, then you might want to drain the water and refill the bin. Add more detergent before returning your brace to the wash bin.
Rinse the brace by refilling the wash bin with clean, cool water. Drain the wash bin, rinse it, then refill it with clean water. Place the brace in the water, then gently move it in an up-and-down motion to remove the soap. You may need to refill the tub with clean water more than once to get all of the soap out. Don’t run the water directly over your brace, as this can damage your brace.
Let the brace air dry on a flat surface. Place the brace on a waterproof surface, such as a countertop or plastic tablecloth. Alternatively, lay it out on a towel. If you want to speed up drying, you can place the brace in the sun. Don’t replace the plastic or metal pieces until after your brace is dry.
Washing Your Brace in a Washing Machine
Check the label to make sure it can go in the washing machine. Most braces cannot be washed in a machine, so make sure that yours can. If it can be washed in the machine, follow all of the instructions on the label. If you wash your brace inappropriately, then you may damage it. Even if the brace has a warranty, the company will not replace it if you washed it incorrectly.
Remove any hinges or clasps, if they come off. These pieces are easily damaged in a washing machine. They can also cause damage, especially in the case of metal clasps or plates. If these pieces are dirty, you can wipe them down with a soapy towel, then dry them with a clean, dry towel. If they don’t come off, then you should close them.
Set your washing machine on a gentle cycle. Your washing machine should have a knob or button that allows you to adjust the setting. This lighter setting is less likely to damage the fabric. You can also use a delicate cycle.
Set the water temperature to “cold.” Your washing machine should have a knob or button that allows you to change the water temperature. Cold water is safer for your fabric, but it will still get your brace clean. If the label says it’s okay, you can use warm water instead.
Add a mild detergent to your washer. Follow the directions on the detergent label to determine how much to add. Use the amount suggested for a small load of laundry. Do not use bleach on your brace, even if it’s white. This can weaken the fabric.
Allow the brace to air dry. Place your brace on a waterproof surface, such as a countertop. You can also lay it out on a towel. If you want it to dry faster, you can place it in the sun. Do not put your brace in the dryer.
Keeping Your Brace Clean
Wash your brace every 4-6 days for daily wear. Even if you wear your brace every day, you’ll only need to wash it once or twice a week, unless you get it very dirty. This is enough to prevent your brace from becoming infected with bacteria or fungi, such as ringworm. If you wear your brace during athletics, wash your brace every 2-3 days. If you do a dirty activity, such as gardening, wash the brace directly after that activity.
Spray the brace with a disinfectant between washes. Apply the disinfectant as soon as you take it off every day. This helps limit the growth of bacteria and microbes without constantly washing the brace. Hold the spray 6 inches (15 cm) over the brace and spritz it in 1 smooth motion. Let your brace dry after you spray the disinfectant.
Allow your brace to air dry for a few hours each day. You need to give your knee a break for at least a few hours each day. Fortunately, that gives your brace time to air out! Make sure that your brace is fully dry before you put it back on. If your brace takes too long to dry, then it’s best to rotate your braces. Do not wear a wet or damp brace.
Comments
0 comment