Most Modern Whirlpool Machines
Unplug the power and wait one minute. Modern Whirlpool machines are computers, and the old “turn it off and on again” trick will reset them. Unplug the machine from the wall outlet and wait 60 seconds before plugging the machine back in. If the machine is hardwired into the wall or you’d have to pull out the entire machine to access the outlet, just flip the fuse connected to the washing machine off and wait 1 minute. If you don’t know where the fuse is, you can flip the main power breaker instead. If you see the word “Cabrio” on your machine’s panel, see our section on Cabrios.
If “Loc” is displayed, press and hold the “control lock” button. Most Whirlpool machines have a control lock designed to shut everything off and lock the door so kids can’t climb into the drum. It’s possible you hit this button by accident, so find the “control lock” button and press it. If nothing happens, press it and hold the button for at least 5 seconds. Your machine should come back to life. On some machines, you’ll see a little padlock logo pop on when the control lock is active. If you don’t see any buttons labeled “control lock,” try pressing “start” or “start/pause.” Then, try holding them down for at least 5 seconds. If that doesn’t work, find your manual and search for the control lock info.
Modern Machines Option #2
Turn the washer off but leave the power on. There appears to be a period in Whirlpool's history where they used a dial-based reset method, but those instructions appear to be relatively hard to find on their website. If you have a newer model but unplugging it and unlocking the control lock doesn’t work, try turning the cycle off. Leave the power on the washer on, though. Then, perform the following steps: Turn the dial mode to “normal” Turn the dial counter-clockwise for 1 click. Turn the dial clockwise for 3 clicks. Turn the dial counterclockwise for 1 click. Turn the dial clockwise for 1 click. Press the start button. If only 3 lights come on, you’re good to go. If all the cycle lights come on, press “start/stop” once. Rotate the dial until you see “rinse,” “wash,” and “stop” illuminated. Then, unplug the machine, wait 10 seconds, and plug it back in.
Recalibrating Top Load Washers
Open and close the lid 6 times in 12 seconds. This is a solution for GE washers. However, some Whirlpool owners have had success using this method with top-loading machines. Since completing this one is so easy, give it a shot! Open and close the lid rapidly at least 6 times in 12 seconds. Your machine may reset.
Cabrios
Press “pause/cancel,” choose a cycle, then press start. If you have an older Whirlpool washing machine, you’ve probably got one of their Cabrio models. These were their most popular line at the time, and many are still out there today. If your Cabrio isn’t responsive or something seems off, start by pressing “pause/cancel” or “pause.” Then, select a wash cycle on the dial and hit the start button. Whirlpool stopped making them around ten years ago, so if your washer feels like it’s on the newer side and you don’t see “Cabrio” on the top panel, it’s probably not a Cabrio.
Disconnect the power, plug it back in, and wait 10 minutes. Do not pause the cycle. Shut the machine down by pulling the plug out from the wall. If the washer is hardwired into the wall or you can't reach the outlet, flip the circuit on the fuse box. Then, wait at least 10 minutes. This interrupts the machine’s natural cycle. It will force reset over the next 5-10 minutes as the electrical charge drains.
Run an empty load to help the washer recalibrate. After 10 minutes or so, plug the washing machine back into the wall or flip the circuit breaker. Then, run whatever wash cycle the dial is sitting on with nothing in the drum. The washing machine will be all good to go after that load is finished. If you can’t get the cycle to run or the machine is still not running properly, it may be time to replace your washer. On average, washing machines only last around ten years, and that’s about how old most Cabrios are at this point.
Reasons the Washer Won’t Start
Inadequate power Check your outlet to ensure your machine is plugged in. If it is, test the outlet itself by plugging a phone charger in to confirm it works. If the phone charger works but the machine isn’t turning on, it’s likely that the outlet isn’t providing enough voltage for the washing machine. Alternatively, there could be something wrong with your machine’s electrical wiring. The Solution: If the outlet does appear to be working, try flipping the fuse on and off. If that doesn’t fix the problem, contact an electrician to have the problem diagnosed by a pro.
Overheated machine If you’ve been running the machine repeatedly for multiple hours now, it’s possible that your washer’s components are just running too hot. Put your hand on the side of the machine. If it’s really warm, you’re probably close to blowing the washer’s engine out. The Solution: Wait a few hours. Give your machine a rest and wait for the heat to dissipate. In the future, try to avoid running more than 2-3 cycles in a row. If your engine still overheats, contact a repair company.
Wrong cycle configuration If the control lock is activated or you accidentally hit the “delay start” button, your washer won’t activate even when you press the “start” button. The Solution: Reset your cycle. If you don’t know how (or why the machine locked in the first place), just unplug it and wait 10 minutes before plugging it back in.
Damaged door switch If you don’t hear a little click when you close the door all the way or you can easily open the Whirlpool’s lid without any resistance, the door switch is likely broken. Most Whirlpool machines will not start if the door isn’t locked and secured. The Solution: Contact an appliance repair company or reach out to Whirlpool if your warranty is still good. The lid likely needs to be replaced.
Comments
0 comment