How to Make a Memory Wire Bracelet

Making a Basic Bracelet

Measure out at least three coils of memory wire, add 1 inch (2.54 centimeters), and cut it using a pair of wire cutters. Do not use your good, jewelry wire cutters; they are much too delicate. Use pair of heavy duty ones instead. Memory wire is hard, and it can easily dull a good pair of wire cutters.

Use your round-nose plies to make a small loop at one end of the wire. Pinch the end of your wire with a pair of round-nose pliers. Twist the wire around the top of the pliers to form a loop, then pull the pliers out. Use the plies to squeeze the loop smaller, if needed. This will hold the beads in place and prevent them from sliding off the end of the wire.

Thread your beads onto the wire, leaving a ½ inch (1.27 centimeter) tail. You can use different shapes, sizes, and colors of beads, or just one type for something simple. You can even use a different type of bead on each coil. Don't cover the entire wire with beads. Leave a ½ inch (1.27 centimeters) tail at the end.. Small beads, such as bicorns and seed beads work great for memory wire bracelets. Avoid using any large, chunky beads, especially towards the end, as they might slide past the loops.

Fold the tail end of the wire into another loop. Pinch the end of the wire with your round-nose pliers, and wrap the wire around it to form a loop. Pull the pliers out, and use them to pinch the loop smaller, if necessary.

Consider adding a charm using a jump ring. Use a pair of needle-nose pliers to pull apart a jump ring. Slip a charm onto the jump ring, then place the ring where you want it on the bracelet. Use the needle-nose pliers to close the ring. Great places to put charms include at either end of the bracelet, or in the middle between two beads.

Finished.

Making a Braided Bracelet

Cut 9 coils of memory wire. You will end up with 9 rings made out of memory wire. You can have the ends of the rings overlap a little if you'd like extra space on your bracelet. Do not use your good, jewelry wire cutters for this, or they may get ruined. Use a sturdy pair of hardware pliers instead. For a thicker bracelet, cut 12 coils.

Use a pair of round-nose pliers to make a small loop at one end of each piece of memory wire. Pinch the end of a piece of wire with the round-nose pliers. Wrap the wire over the top of the pliers to form a loop. Pull the pliers out, then pinch the loop smaller if it is too big. Do not make a loop on both ends of the wire pieces or you won't be able to get the beads on.

String your beads onto the wires, leaving a ½ inch (1.27 centimeters) tail of bare wire. The best beads to use are seed beads, but you can add some larger, bicone beads in various places for a more interesting design. Do not cover the entire wire with beads; you need that gap at the end so that you can "close" the wire.

Use your round-nose pliers to make another loop at the end of each piece of beaded memory wire. This will close the wire and prevent the beads from falling off. Once you are done with all of the pieces, set them aside.

Cut two 2-inch (5.08 centimeters) pieces of regular, 20-gauge beading wire. You will be using these to hold your beaded memory wire strands together.

Make a small loop at the top of each piece of beading wire. The loop should be fairly small, but big enough so that the doesn't slip through the end loops on your beaded memory wire coils.

String the memory wires onto one of the short beading wires. You can separate the memory wire coils with a seed bead or a spacer bead, if you'd like something fancier. Make sure that all of the memory wires are coiled in the same direction.

Close the bottom of the short wire with a loop. Once you have gotten all of the memory wire coils onto the short wire, use a pair of wire cutters to trim it down to ½ inch (1.27 centimeters). Use the round-nose plies to fold the end of the short wire into a small loop. This will hold your memory wire strands together.

Braid the memory wires. Separate the wires into three groups. If you used 9 coils, each group should have 3 strands. If you used 12 coils, each group should have 4 strands. Loosely braid the strands together.

Slip the remaining short wire through the end loops on the beaded memory wire strands, and close it with a loop. If you used seed beads or spacer beads on the first short wire, remember to use them here too. Your bracelet is now complete and ready to wear!

Making a Leather Cord Bracelet

Cut 3 coils of some memory wire. Get some memory wire, and measure out three coils. Cut them using a pair of wire cutters. Try to use the heavy duty kind, and not your good jewelry wire cutters. Memory wire is strong, and can easily dull a good pair of wire cutters.

Cut 18 inches (45.72 centimeters) of braided leather cord. You must use braided leather cord. Regular leather cord won't work because it doesn't have any room inside for the wire. The recommended size is 6mm. If you can't get cord in that size, use the next closest one you can find.

Wrap tape around the ends of the cord to prevent it from fraying. Do not tape over the ends, or you won't be able to feed the fire through it. Try to use a narrow piece of tape; cut it in half lengthwise if needed. You will be leaving the tape on the cord. If it is too wide, it will peak out from under the caps.

Feed the wire through the cord. Some cords have rubber tubing inside. If your cord has rubber tubing, simply thread the wire through it. You may have to use a pair of pliers to pull the wire through the cord at the end.

Trim the wire back from both ends of the coil, so that you have 2¾ coils. This will make it easier to slip the end caps on. To trim the wire, push the cord down a little, the cut the wire using a pair of wire cutters. Repeat this step for the other end of the coil as well.

Glue an end cap or cord cap onto each end of the cord. Place a few drops of super glue into the cup part of the cap, then push the cap onto the end of the cord. You will need to twist the cap in order to get it all the way on. Repeat for the other end of the bracelet. The tape should be covered completely by the cap, so you should not have to remove it. The recommended size is 6mm. If you are using a different sized cord, however, then make sure that you get caps that match that cord. For example, if your cord is 4mm, then get 4mm caps. If you'd like to add charms to your caps, get the kind that have loops on the end. You can use any color your want, but silver will look best with black leather; brass will look best with brown leather.

Wait 30 minutes for the glue to dry, then add some charms, if desired. Open up a jump ring, then slip a charm into it. Poke one of the ends of the jump ring through the loop at the end of an end cap, then close it. If you'd want a simpler bracelet, you can skip this step.

Let the glue dry completely before wearing the bracelet. This may take up to 24 hours. Once the glue has dried, your bracelet is ready to wear.